Dual LED Battery-Powered Wireless Indoor/Outdoor Motion Light

Limitless Innovations

Dual LED Battery-Powered Wireless Indoor/Outdoor Motion Light

The Lumenology Dual Motion Light provides an impressive 1000 lumens from two high-luminance white LED bulbs. Install the light virtually anywhere with the adjustable bracket or clamp. The IP44 water resistance rating equips it for outdoor use, even in the elements. MotionSense technology provides a 20-foot detectable range and 140-degree field-of-view, which will detect motion in both dark and light environments with the built-in LightSense technology.

Includes

One (1) Lumenology Dual Motion Light in White or Bronze
One (1) clamp
One (1) L-rod
One (1) butterfly nut
One (1) plastic cap
Four (4) plastic anchors
Four (4) screws
User manual

Features

Ultra-bright, two-headed LED motion light provides powerful 1000 lumens of high-luminance white light that will instantly improve a home’s security
The 360° adjustable heads customize the light coverage to suit any environment
The 20 ft detectable range and 140° field-of-view detects motion in dark and light environments

Three user modes: Motion-activated 10-second, 20-second, or 30-second with auto shut-off
Can be installed on a ceiling, wall, railing, tree, and more
No electricity or wiring required
Great for use indoors and outdoors, even in the elements
Water resistance rating of IP44
High-luminance white light
Color temperature: 5800 K
Beam distance: 144 ft
LED battery: 3x D Dry Cell (not included)
Batteries last for approx. 1530 activations (based on 30-second auto shut off) or 7 hours on “stay-on” mode
Measures 11.06" x 3.75" x 5.8"
Weighs 1.4 lbs

How to Use

Set up:
- Turn the battery cover thumb screw counterclockwise until the battery cover is detached from the battery box of the Lumenology Dual Motion Light and pull away
- Disengage the inner battery cover by pressing down where the inner battery cover is labeled “push” and pull away
- Note: The inner battery cover does not disconnect completely. It rotates on a 90° axis. Do not push against the inner battery cover when it is open as it may break
- Insert 3x D batteries (not included) and be sure to align the positive (+) and negative (-) terminals correctly
- Caution: Some equipment using three or more batteries may appear to work properly even if one battery is inserted incorrectly; such usage may lead to battery leakage or rupture that could result in equipment damage
- Rotate the inner battery cover back into place. Push in until it clicks and does not rotate freely
- Close the battery box by first aligning the three tabs on the battery cover to the three notches in the battery box
- Turn the battery cover downward until completely closed
- Rotate the battery cover thumb screw clockwise until the battery cover is tightened and secured to the battery box
Sensor detection range:
- The motion sensor can detect movement in a max field-of-view of 140° and a max distance of 20 ft
- Notes:
  - The motion sensor is less likely to detect motion when walking directly towards the unit
  - The detection area performs best when set to a height of 6.5 ft (2 m) high
Installation:
- Using bracket:
  - Measure, locate, and mark where the Lumenology Dual Motion Light will be installed
  - Note: It is recommended to install the Lumenology Dual Motion Light directly to a wooden stud, metal stud, or plywood wall sheathing
  - Place the mounting bracket on the spot you marked
  - Using a pencil, mark the location through the 4 mounting holes
- Wood stud, metal stud, or plywood wall sheathing: Fasten the mounting bracket directly to the wall with the 4 included screws. No additional anchors are necessary
- Dry wall without stud:
  - Remove the mounting bracket to expose the marks made in step above
  - Pre-drill 1/8” holes at each of the marked locations
  - Insert an anchor into each drilled hole from the previous steps. You may need to lightly hammer the anchors in place
  - Place the mounting bracket to align the mounting holes with the anchors
  - Fasten the Lumenology Dual Motion Light to wall with the 4 supplied screws
- Concrete:
  - Remove the mounting bracket to expose the previously made marks
  - Pre-drill 1/4” holes at each of the marked locations
  - Insert an anchor into each drilled hole from the previous step. You may need to lightly hammer the anchors in place
  - Place the mounting bracket to align the mounting holes with the anchors
  - Fasten the Lumenology Dual Motion Light to wall with the 4 supplied screws
Using clamp:
- Slide the threaded end of the L-rod through the clamp
- Thread the butterfly nut onto the L-rod by rotating clockwise. Do not thread all the way down at this time
- Add plastic cap to the threaded end of the L-rod
- Insert the flat end of the L-rod into the L-rod slots on the mounting bracket
- Rotate the L-rod 90° to keep the Lumenology Dual Motion Light from sliding off
- Place the Lumenology Dual Motion Light with the hanging surface in-between the clamp and mounting bracket
- Once the Lumenology Dual Motion Light is in the desired position, continue to thread the butterfly nut clockwise until tight and secure
- Adjust the LED lights, adjustable arm, and motion sensor until satisfied with the positioning
Adjusting the motion sensor:
- Grab the motion sensor along two sides and rotate left, right, up, or down until the preferred positioning is achieved
- Notes:
  - Do not force any movement as it may cause damage to the motion sensor
  - The motion sensor will only rotate left/right 160° and up/down 30°
- Maximum field-of-view: Adjust the motion sensor horizontally
- Minimum field-of-view: Adjust the motion sensor diagonally downward
Adjusting the body position:
- Loosen the adjustment knob by turning counterclockwise and the adjustment arm moves freely
- Rotate and move the Lumenology Dual Motion Light until the desired position is reached
- Hold and re-tighten the adjustment knob by turning it clockwise
- For additional movement to the adjustable arm, loosen with the bracket-to-arm screw by turning counterclockwise. This will allow the adjustable arm to rotate an additional 160° side-to-side. Once the desired positioning is achieved, re-tighten the bracket-to-arm screw by turning clockwise
- Note: For complete adjustment capabilities, loosen the adjustment knob and bracket-to-arm screw at the same time
Setting the mode:
- Adjust the light sensitivity knob to align the dial to day, night, or somewhere in-between to better suit the surroundings or preferences
- Day: LED light is activated by motion regardless of whether the surrounding area is bright or dark
- Night: LED light is only activated by motion when the surrounding area is dark
- Note: If additional light is preferred in a bright environment, the light sensitivity knob should be moved to the day position
Setting the duration:
- To adjust the timer, turn the timer knob until the dial aligns with one of the time durations:
  - 10s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 10 seconds unless motion is detected again
  - 20s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 20 seconds unless motion is detected again
  - 30s: Once motion is sensed and the LED light is activated, the LED light will remain on for approximately 30 seconds unless motion is detected again
- Note: The angle between durations is not proportional to time
Red LED indicator light:
- The red LED indicator light will flash at different intervals depending on certain criteria:
  - Blinks once every 5 seconds: Standby mode
  - Blinks quickly: Motion sensor is detecting movement
  - Blinks once every second: The batteries are low and the LED lights will only activate in darkness
  - Off: There are no batteries in the Lumenology Dual Motion Light or the batteries need to be replaced
- Note: The red LED indicator light is easiest viewed in a dark environment

Care Instructions

Please keep the Lumenology Dual Motion Light and all accessories out of reach of small children
Do not use third party power supplies or non-approved adapters with the Lumenology Dual Motion Light
Do not attempt to open the outer casing of the Lumenology Dual Motion Light
Do not clean the Lumenology Dual Motion Light with harsh chemicals and keep the Lumenology Dual Motion Light away from liquids
Do not expose the Lumenology Dual Motion Light to extreme temperatures
Do not paint or apply coatings to the Lumenology Dual Motion Light, as you might affect moving parts or damage internal components
Do not stick foreign objects in any port/opening of the Lumenology Dual Motion Light. Doing so may cause electric shock
Do not attempt to disassemble or repair the Lumenology Dual Motion Light
Do not drop the Lumenology Dual Motion Light. Doing so may damage internal components otherwise not seen and must not be operated
Do not submerge the Lumenology Dual Motion Light or its accessories in water
Disassembling the Lumenology Dual Motion Light, including the removal of external screws, may cause damage that is not covered under the warranty
Do not mix new and old batteries. It may cause the LED light to malfunction
Do not look directly at the LED light
Do not mix Alkaline, Standard (Carbon-Zinc), or Rechargeable (Nickel Cadmium) or (Nickel Metal Hybrid) batteries
Do not install the main body in places where a large amount of water may come in contact with the Lumenology Dual Motion Light
Do not use near home electric appliances
Do not install diagonally, downward, or upside down regardless of indoor or outdoor use as it may cause failure
Do not install near combustible objects
Do not install near flammable materials such as cloth, paper, or objects that may easily catch fire
Do not use manganese, dry, or rechargeable batteries. It may cause a malfunction due to voltage shortage
Do not install near appliances emitting radio waves as it may cause failure
Do not install near motors or devices generating a magnetic field. May cause failure